Cannon-instrument miniAV-LT Manuale Utente Pagina 58
- Pagina / 124
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
CANNON
®
miniAV-LT Automatic Viscometer with VISCPRO
®
Instruction & Operation Manual
Version 1.a— May, 2009; CANNON
®
Instrument Company
2139 High Tech Road • State College, PA 16803 • USA
54
If the Always perform maximum determinations radio button is selected,
the last flow times will be used for the viscosity determination.
When you have completed the configuration and saved the current
settings, you may wish to permanently store the settings using the Save
Instrument and Tray Settings.Tray Settings: Wash
Use the Tray Settings: Wash window to determine wash settings. For
multi-tube units, different wash settings may be selected for each tube
individually.
The Tray Settings: Wash window (Dual Solvent options shown)
Solvent rinse settings
The solvent rinse settings for Solvent A and (if applicable) Solvent B are
determined using the Tray Settings: Wash window. Select a value from
0 to 18 cycles for this option (the “0” setting turns the solvent option off).
These settings determine the number of rinse cycles performed by the
miniAV-LT instrument after each test. Higher viscosity materials may
require more rinses. Lower viscosity materials may require fewer rinses,
depending on the effectiveness of the solvent.
- CONTENTS 1
- CALIBRATING THE miniAV 29 2
- USING THE miniAV SOFTWARE 37 2
- OPERATING, MAINTAINING 3
- AND SERVICING THE miniAV 73 3
- INTRODUCTION/INSTALLATION 5
- Measuring kinematic viscosity 6
- Safety cautions 6
- Installing VISCPRO 11
- software 11
- Running the software 12
- Checking configuration 13
- Logging in 14
- Checking Instrument Settings 14
- Prompt options 15
- Sample calibration constants 16
- Procedure 17
- The Calibration window 18
- Inserting the probes 20
- Inserting the thermometer 20
- Setting bath temperature 21
- Checking wash functions 22
- Training tube sensors 23
- Calibrating the miniAV-LT 23
- TESTING SAMPLES WITH THE 25
- VISCOMETER 25
- Running check standards 27
- Pausing a test 28
- Resuming a test 28
- Aborting a test 28
- Concluding a test 28
- The Machine Status window 29
- Group configuration 30
- Viewing test results 31
- Creating an analysis 31
- VI Matching with VISCPRO 32
- CALIBRATING THE miniAV-LT 33
- Training sensors 34
- Train Tube Sensors 35
- Standard tube calibration 36
- Selecting samples 38
- Comparing current/new data 38
- Saving a calibration 39
- USING THE miniAV-LT 41
- SOFTWARE 41
- Main Menu 42
- Security options 43
- Initial security setup 43
- Adjusting Security Settings 45
- Analyses Menu 46
- The Choose Analysis window 47
- Window Menu 48
- Configure menu 49
- Instrument Settings 52
- Tray Settings: Tube and Bath 54
- Bath Temperature 55
- Equilib. Tolerance 55
- Thermistors Radio Buttons 55
- Soak Time Units Radio Buttons 55
- Soak time 56
- Constants 56
- Tray Settings: Test 56
- Tolerance parameters 56
- Use greater 57
- Determinations 57
- Solvent rinse settings 58
- Max Solvent fill time(s) 59
- Solvent flush time(s) 59
- Tube tip soak time(s) 59
- Final dry time(s) 59
- Tray Settings: Advanced 60
- Maximum bulb 1 fill time(s): 61
- Maximum bulb empty time(s): 61
- Calibration 62
- Show Calibration Data 63
- Service menu 64
- Prewash option 67
- Trip Points Only option 67
- Selecting sample actions 69
- Sample actions 70
- Viscosity Action window 70
- The Viscosity Action window 70
- The Sample Action popup 70
- Copying Sample IDs 72
- Pasting Sample IDs 72
- Copying/pasting multiple IDs 72
- Saving Sample ID information 73
- Configuring the VI Matcher 74
- Configuration procedure 75
- Handling errors 76
- AND SERVICING THE miniAV-LT 77
- Solvent Dispensing System 78
- Emptying the Waste Receiver 79
- Viscometer tubes 80
- Temperature bath 81
- Ventilation 82
- Checking bath temperature 82
- Dual-solvent washing 83
- Solvent wash by computer 83
- Preventive maintenance 83
- ?etelpmoC ecnanetniamtneuqerF 84
- ANALYSIS CONFIGURATION 85
- Sorting analysis data 86
- Using the date filter 87
- Using the sample filter 88
- Resizing table columns 89
- Saving a current analysis 90
- Printing an analysis 90
- Exporting analysis data 91
- SAMPLE DATA TABLE 93
- Reporting options 94
- Report filter 96
- Selecting 96
- Modifying data presentation 96
- SAMPLE DATA EXPORT ANALYSIS 99
- Date/Sample filters 100
- Port Output Format filter 100
- Adding ports 100
- The Port Output Format window 101
- Configuring output 101
- Delaying serial output 101
- Selecting output data 101
- Adding a footer 102
- Adding a header 102
- Re-sending export data 103
- Port selection 103
- ERROR DATA EXPORT ANALYSIS 105
- Date filter 106
- Error Page filter 106
- The Error Page tab 107
- ERROR LOG TABLE ANALYSIS 111
- The Save Configuration window 113
- USING THE DATABASE 115
- Archiving old data 116
- Importing archived data 117
- REPLACEMENT PARTS LIST 119
- APPENDIX A–MULTIPLE UNIT 121
- CONFIGURATION 121
Prodotti e manuali riguardandi Strumenti di misura Cannon-instrument miniAV-LT
(6 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.181 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale